Hilti TE 2-M Operations Instructions download pdf (Page 7)

The tool is designed for the following uses:

Use Required insert tools Diameter range

TE 2 / TE2-E / TE2-S / TE 2-M:

Hammer drilling in concrete, Drill bits with TE-C connection end Drilling in concrete:

masonry and natural stone – Short hammer drill bits Anchor holes of 4–22 mm dia.

– Long hammer drill bits Through holes of 4–22 mm dia.

TE 2-S:

Drilling with precision Drill bits with TE-C connection end Drilling in brittle materials:

hammering action in perforated – TE-C hammer drill bits Anchor holes of 4–22 mm dia.

brick, tiles and marble – Thin-barrel core bits Cutting sockets of 25–68 mm dia.

TE 2 / TE2-E / TE2-S:

Drilling in wood, drywall panels Quick-release chuck with TE-C adaptor for insert

and metal tools with cylindrical shank or hexagonal shank

for rotary-only drilling

Wood drill bits 4–20 mm dia.

Metal drill bits 3–13 mm dia.

Hole saws 25–68 mm dia.

TE 2-M:

Drilling in wood, drywall panels, Interchangeable quick-release chuck for

tiles and metal insert tools with cylindrical shank or hexagonal

shank for rotary-only drilling:

Wood drill bits 4–10 mm dia. in 2nd gear

10–20 mm dia. in 1st gear

Metal/stepped drill bits 3– 8 mm dia. in 2nd gear

8–13 mm dia. in 1st gear

Hole saws 25–68 mm dia. in 1nd gear

 The numbers refer to the illustrations. The illustrations

can be found on the fold-out cover pages. Keep these

pages open while you read the operating instructions.

In these operating instructions, the power tool to which

these operating instructions apply is referred to as “the

tool”.

Description

The TE2 / TE2-E / TE2-S / TE2-M is an electrically pow-

ered rotary hammer with pneumatic hammering mech-

anism designed for professional use.

The following items are supplied: power tool, (quick-

release chuck TE2-M), operating instructions, grease

(except TE 2-E), toolbox, side handle, cleaning cloth,

Depth gauge.

The following conditions must always be observed

when the tool is in use:

– The tool must be connected to an alternating current

electric supply in compliance with the information

given on the type plate.

– The tool is for hand-held use only.

– The tool must not be used in places where the sur-

rounding conditions may present a risk of explosion.

– Changes or modifications to the tool are not per-

missible.

– To avoid the risk of injury, use only the genuine Hilti

accessories and additional equipment specified for

se with this tool.

– Observe the information printed in the operating

instructions concerning operation, care and main-

tenance. The tool and its ancillary equipment may

present hazards when used incorrectly by untrained

personnel or when used not as directed.

– The tool is intended for professional use.The tool

may be operated, serviced and repaired only by

authorized, trained personnel. This personnel must

be informed of any special hazards that may be

encountered.

Main features of the tool

Class II electrical protection (double insulated) Z

Mechanical torque-limiting clutch

Grip and side handle with vibration absorption

TE-C chuck

TE-C insert tool system

Variable speed switch

Rotary-only drilling mode

Gearing and hammering mechanism with permanent

grease lubrication

Pivotable side handle (360°)

Mechanical depth gauge

Interface for quick-release chuck (TE2-M)

Precision hammering action (TE2-S)

High spindle speed without hammering action (TE2-M)

Lockbutton for sustained operation

Right of technical changes reserved

01_BA_TE2_S_M_P8_en.qxd:02_BA_TE2_S_M_P1_en.qxd 1.10.2012 15:03 Uhr Seite 2

Printed: 03.06.2014 | Doc-Nr: PUB / 5170565 / 000 / 01

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Comments to this Manuals

No comments

Hilti TE 2-M Operations Instructions Page 7

Comments to this Manuals