Hilti 385638 Use and Care Manual

DSH 700/DSH 900*288292*288292Hilti CorporationLI-9494 SchaanTel.:+423 / 2342111Fax:+423 / 2342965www.hilti.comHilti = registered trademark of Hilti Co

or explosion. Take care to ensure that the sparksgenerated do not ignite flammable (gasoline,dry grass, etc.) or explosive (gas, etc.) sub-stances.5.7

chine will run out of balance, vibrate excessivelyand may cause loss of control.j) Always use undamaged disc mounting flangesof the correct diameter f

5100 rpmmax.6.1.3 Mixing fuelCAUTIONThe motor will suffer damage if run with fuel mixedin the wrong ratio or with unsuitable oil. Use thefollowing mix

run out of balance, vibrate excessively and may causeloss of control.CAUTIONDon’t use synthetic resin-bonded fiber-reinforcedcutting discs that have e

DANGERDon’t operate the machine without the protectivedevices that belong to it.In order to facilitate cutting as closely as possible toedges and wall

7. Operation7.1 Starting the motor 7CAUTIONWorking on the material may cause it to splinter.Wear eye protection and protective gloves. Wearbreathing p

13. Press the throttle as soon as the motor starts.This disengages the half-throttle position andthe choke (if previously engaged), and the motorthen

Check the machine for dirt and dust and clean it ifnecessary.Check that all operating controls function correctly.Have them repaired if necessary.Chec

10. Pull the starter cord out as far as it will go andcheck to ensure that the spool can be turnedby hand at least a further ½ turn in a clock-wise di

5. Remove the defective drive belt. Place the newdrive belt carefully over the two drive pulleys.6. Tension the drive belt by turning the belt tension

192"≠+# +] +["Ç+|5 +}+≠ 7 6+±4 +{ "#+“ "“"[+Ç3 "±81ꨍꨏꨔꨑꨎꨐꨕꨒꨓ21/81/842/7/9331/15142/45/13463/1087911412515732/43666256348

3. Clean the machine thoroughly and grease themetal parts.4. Remove the spark plug.5. Pour a little two-stroke oil into the cylinder (1 to2 teaspoons)

Fault Possible cause RemedySaw doesn’t start or is diffi-cult to startNo ignition spark visible or sparkis too weak (when spark plug isremoved).Clean

Fault Possible cause RemedyCutting disc rotates while themotor is idlingIdling speed is too high.Check the idling speed and adjust ifnecessary.The hal

defined by Hilti in the owner’s manual. Hilti recom-mends that you retain all receipts covering mainte-nance on your small non-road engine, but Hilti

For repair or replacement, send the tool or relatedparts immediately upon discovery of the defect tothe address of the local Hilti marketing organizat

ORIGINAL OPERATING INSTRUCTIONSDSH 700/ DSH 900 cut-off sawIt is essential that the operating instruc-tions are read before the machine is oper-ated f

5100 rpmmax.1. General information1.1 Safety notices and their meaningDANGERDraws attention to imminent danger that could leadto serious bodily injury

2. Description2.1 Use of the product as directedThe machine is intended for hand-held or walk-behinduse for dry or wet cutting of asphalt and mineralo

seconds every 30 to 60 seconds while the machine isstill running.To reduce the amount of dust produced when cutting,we recommend use of the wet cuttin

4. Technical dataRight of technical changes reserved.MachineDSH 700 30 cm/ 12"DSH 700 35 cm/ 14"DSH 900 35 cm/ 14"DSH 900 40 cm/ 16&quo

MachineDSH 700 30 cm/ 12"DSH 700 35 cm/ 14"DSH 900 35 cm/ 14"DSH 900 40 cm/ 16"Max. disc thick-ness (steel discthickness)5.5 mm (0

t) Children must be instructed not to play with themachine.u) The appliance is not intended for use by childrenor debilitated persons.v) Lifting the s